Accumulated patchsets for bsp/cvitek

bsp/cvitek/c906_little/Kconfig

@@ -39,20 +39,32 @@ config TIMER_CLK_FREQ
     int
     default 25000000
 
+config SOC_TYPE_CV180X
+    bool
+    default n
+
+config SOC_TYPE_SG2002
+    bool
+    default n
+
 choice
     prompt "Board Type"
     default BOARD_TYPE_MILKV_DUO256M
 
     config BOARD_TYPE_MILKV_DUO
+        select SOC_TYPE_CV180X
         bool "milkv-duo"
 
     config BOARD_TYPE_MILKV_DUO_SPINOR
+        select SOC_TYPE_CV180X
         bool "milkv-duo-spinor"
 
     config BOARD_TYPE_MILKV_DUO256M
+        select SOC_TYPE_SG2002
         bool "milkv-duo256m"
 
     config BOARD_TYPE_MILKV_DUO256M_SPINOR
+        select SOC_TYPE_SG2002
         bool "milkv-duo256m-spinor"
 
 endchoice

bsp/cvitek/c906_little/board/Kconfig

@@ -20,7 +20,7 @@ menu "General Drivers Configuration"
         endif
 
     menuconfig BSP_USING_I2C
-        bool "Using HW I2C"
+        bool "Using I2C"
         select RT_USING_I2C
         select RT_USING_I2C_BITOPS
         select RT_USING_PIN
@@ -29,15 +29,130 @@ menu "General Drivers Configuration"
         if BSP_USING_I2C
             config BSP_USING_I2C0
                 bool "Enable I2C0"
+                depends on BOARD_TYPE_MILKV_DUO || BOARD_TYPE_MILKV_DUO_SPINOR
                 default n
 
+                if BSP_USING_I2C0
+                    choice
+                        prompt "SCL"
+
+                        config BSP_USING_IIC0_SCL__IIC0_SCL
+                            bool "IIC0_SCL/GP0"
+                    endchoice
+
+                    choice
+                        prompt "SDA"
+
+                        config BSP_USING_IIC0_SDA__IIC0_SDA
+                            bool "IIC0_SDA/GP1"
+                    endchoice
+                endif
+
             config BSP_USING_I2C1
                 bool "Enable I2C1"
                 default n
 
+                if BSP_USING_I2C1
+                    choice
+                        prompt "SCL"
+
+                        if BOARD_TYPE_MILKV_DUO || BOARD_TYPE_MILKV_DUO_SPINOR
+                            config BSP_USING_SD1_D2__IIC1_SCL
+                                bool "SD1_D2/GP4"
+                            config BSP_USING_SD1_D3__IIC1_SCL
+                                bool "SD1_D3/GP9"
+                            config BSP_USING_PAD_MIPIRX0N__IIC1_SCL
+                                bool "PAD_MIPIRX0N/GP11"
+                        endif
+
+                        if BOARD_TYPE_MILKV_DUO256M || BOARD_TYPE_MILKV_DUO256M_SPINOR
+                            config BSP_USING_SD1_D2__IIC1_SCL
+                                bool "SD1_D2/GP4"
+                            config BSP_USING_SD1_D3__IIC1_SCL
+                                bool "SD1_D3/GP9"
+                        endif
+
+                    endchoice
+
+                    choice
+                        prompt "SDA"
+
+                        if BOARD_TYPE_MILKV_DUO || BOARD_TYPE_MILKV_DUO_SPINOR
+                            config BSP_USING_SD1_D1__IIC1_SDA
+                                bool "SD1_D1/GP5"
+                            config BSP_USING_SD1_D0__IIC1_SDA
+                                bool "SD1_D0/GP8"
+                            config BSP_USING_PAD_MIPIRX1P__IIC1_SDA
+                                bool "PAD_MIPIRX1P/GP10"
+                        endif
+
+                        if BOARD_TYPE_MILKV_DUO256M || BOARD_TYPE_MILKV_DUO256M_SPINOR
+                            config BSP_USING_SD1_D1__IIC1_SDA
+                                bool "SD1_D1/GP5"
+                            config BSP_USING_SD1_D0__IIC1_SDA
+                                bool "SD1_D0/GP8"
+                        endif
+                    endchoice
+                endif
+
+            config BSP_USING_I2C2
+                bool "Enable I2C2"
+                depends on BOARD_TYPE_MILKV_DUO256M || BOARD_TYPE_MILKV_DUO256M_SPINOR
+                default n
+
+                if BSP_USING_I2C2
+                    choice
+                        prompt "SCL"
+
+                        config BSP_USING_PAD_MIPI_TXP1__IIC2_SCL
+                            bool "PAD_MIPI_TXP1/GP11"
+                    endchoice
+
+                    choice
+                        prompt "SDA"
+
+                        config BSP_USING_PAD_MIPI_TXM1__IIC2_SDA
+                            bool "PAD_MIPI_TXM1/GP10"
+                    endchoice
+                endif
+
+            config BSP_USING_I2C3
+                bool "Enable I2C3"
+                default n
+
+                if BSP_USING_I2C3
+                    choice
+                        prompt "SCL"
+
+                        if BOARD_TYPE_MILKV_DUO || BOARD_TYPE_MILKV_DUO_SPINOR
+                            config BSP_USING_SD1_CMD__IIC3_SCL
+                                bool "SD1_CMD/GP7"
+                        endif
+
+                        if BOARD_TYPE_MILKV_DUO256M || BOARD_TYPE_MILKV_DUO256M_SPINOR
+                            config BSP_USING_SD1_CMD__IIC3_SCL
+                                bool "SD1_CMD/GP7"
+                        endif
+                    endchoice
+
+                    choice
+                        prompt "SDA"
+
+                        if BOARD_TYPE_MILKV_DUO || BOARD_TYPE_MILKV_DUO_SPINOR
+                            config BSP_USING_SD1_CLK__IIC3_SDA
+                                bool "SD1_CLK/GP6"
+                        endif
+
+                        if BOARD_TYPE_MILKV_DUO256M || BOARD_TYPE_MILKV_DUO256M_SPINOR
+                            config BSP_USING_SD1_CLK__IIC3_SDA
+                                bool "SD1_CLK/GP6"
+                        endif
+                    endchoice
+                endif
+
             config I2C_IRQ_BASE
-            int
-            default 32
+                int
+                default 32
         endif
 
     config BSP_USING_ADC

bsp/cvitek/cv18xx_risc-v/Kconfig

@@ -46,20 +46,32 @@ config __STACKSIZE__
     int "stack size for interrupt"
     default 4096
 
+config SOC_TYPE_CV180X
+    bool
+    default n
+
+config SOC_TYPE_SG2002
+    bool
+    default n
+
 choice
     prompt "Board Type"
     default BOARD_TYPE_MILKV_DUO256M
 
     config BOARD_TYPE_MILKV_DUO
+        select SOC_TYPE_CV180X
         bool "milkv-duo"
 
     config BOARD_TYPE_MILKV_DUO_SPINOR
+        select SOC_TYPE_CV180X
         bool "milkv-duo-spinor"
 
     config BOARD_TYPE_MILKV_DUO256M
+        select SOC_TYPE_SG2002
         bool "milkv-duo256m"
 
     config BOARD_TYPE_MILKV_DUO256M_SPINOR
+        select SOC_TYPE_SG2002
         bool "milkv-duo256m-spinor"
 
 endchoice

bsp/cvitek/cv18xx_risc-v/board/Kconfig

@@ -31,7 +31,143 @@ menu "General Drivers Configuration"
             default n
 
         endif
-
+
+    menuconfig BSP_USING_I2C
+        bool "Using I2C"
+        select RT_USING_I2C
+        select RT_USING_I2C_BITOPS
+        select RT_USING_PIN
+        default n
+
+        if BSP_USING_I2C
+            config BSP_USING_I2C0
+                bool "Enable I2C0"
+                depends on BOARD_TYPE_MILKV_DUO || BOARD_TYPE_MILKV_DUO_SPINOR
+                default n
+
+                if BSP_USING_I2C0
+                    choice
+                        prompt "SCL"
+
+                        config BSP_USING_IIC0_SCL__IIC0_SCL
+                            bool "IIC0_SCL/GP0"
+                    endchoice
+
+                    choice
+                        prompt "SDA"
+
+                        config BSP_USING_IIC0_SDA__IIC0_SDA
+                            bool "IIC0_SDA/GP1"
+                    endchoice
+                endif
+
+            config BSP_USING_I2C1
+                bool "Enable I2C1"
+                default n
+
+                if BSP_USING_I2C1
+                    choice
+                        prompt "SCL"
+
+                        if BOARD_TYPE_MILKV_DUO || BOARD_TYPE_MILKV_DUO_SPINOR
+                            config BSP_USING_SD1_D2__IIC1_SCL
+                                bool "SD1_D2/GP4"
+                            config BSP_USING_SD1_D3__IIC1_SCL
+                                bool "SD1_D3/GP9"
+                            config BSP_USING_PAD_MIPIRX0N__IIC1_SCL
+                                bool "PAD_MIPIRX0N/GP11"
+                        endif
+
+                        if BOARD_TYPE_MILKV_DUO256M || BOARD_TYPE_MILKV_DUO256M_SPINOR
+                            config BSP_USING_SD1_D2__IIC1_SCL
+                                bool "SD1_D2/GP4"
+                            config BSP_USING_SD1_D3__IIC1_SCL
+                                bool "SD1_D3/GP9"
+                        endif
+
+                    endchoice
+
+                    choice
+                        prompt "SDA"
+
+                        if BOARD_TYPE_MILKV_DUO || BOARD_TYPE_MILKV_DUO_SPINOR
+                            config BSP_USING_SD1_D1__IIC1_SDA
+                                bool "SD1_D1/GP5"
+                            config BSP_USING_SD1_D0__IIC1_SDA
+                                bool "SD1_D0/GP8"
+                            config BSP_USING_PAD_MIPIRX1P__IIC1_SDA
+                                bool "PAD_MIPIRX1P/GP10"
+                        endif
+
+                        if BOARD_TYPE_MILKV_DUO256M || BOARD_TYPE_MILKV_DUO256M_SPINOR
+                            config BSP_USING_SD1_D1__IIC1_SDA
+                                bool "SD1_D1/GP5"
+                            config BSP_USING_SD1_D0__IIC1_SDA
+                                bool "SD1_D0/GP8"
+                        endif
+                    endchoice
+                endif
+
+            config BSP_USING_I2C2
+                bool "Enable I2C2"
+                depends on BOARD_TYPE_MILKV_DUO256M || BOARD_TYPE_MILKV_DUO256M_SPINOR
+                default n
+
+                if BSP_USING_I2C2
+                    choice
+                        prompt "SCL"
+
+                        config BSP_USING_PAD_MIPI_TXP1__IIC2_SCL
+                            bool "PAD_MIPI_TXP1/GP11"
+                    endchoice
+
+                    choice
+                        prompt "SDA"
+
+                        config BSP_USING_PAD_MIPI_TXM1__IIC2_SDA
+                            bool "PAD_MIPI_TXM1/GP10"
+                    endchoice
+                endif
+
+            config BSP_USING_I2C3
+                bool "Enable I2C3"
+                default n
+
+                if BSP_USING_I2C3
+                    choice
+                        prompt "SCL"
+
+                        if BOARD_TYPE_MILKV_DUO || BOARD_TYPE_MILKV_DUO_SPINOR
+                            config BSP_USING_SD1_CMD__IIC3_SCL
+                                bool "SD1_CMD/GP7"
+                        endif
+
+                        if BOARD_TYPE_MILKV_DUO256M || BOARD_TYPE_MILKV_DUO256M_SPINOR
+                            config BSP_USING_SD1_CMD__IIC3_SCL
+                                bool "SD1_CMD/GP7"
+                        endif
+                    endchoice
+
+                    choice
+                        prompt "SDA"
+
+                        if BOARD_TYPE_MILKV_DUO || BOARD_TYPE_MILKV_DUO_SPINOR
+                            config BSP_USING_SD1_CLK__IIC3_SDA
+                                bool "SD1_CLK/GP6"
+                        endif
+
+                        if BOARD_TYPE_MILKV_DUO256M || BOARD_TYPE_MILKV_DUO256M_SPINOR
+                            config BSP_USING_SD1_CLK__IIC3_SDA
+                                bool "SD1_CLK/GP6"
+                        endif
+                    endchoice
+                endif
+
+            config I2C_IRQ_BASE
+                int
+                default 49
+        endif
+
     config BSP_USING_ADC
         bool "Using ADC"
         select RT_USING_ADC
@@ -42,6 +178,25 @@ menu "General Drivers Configuration"
         select RT_USING_SPI
         default n
 
+    menuconfig BSP_USING_WDT
+        bool "Enable Watchdog Timer"
+        select RT_USING_WDT
+        default n
+
+        if BSP_USING_WDT
+            config BSP_USING_WDT0
+                bool "Enable WDT0"
+                default n
+
+            config BSP_USING_WDT1
+                bool "Enable WDT1"
+                default n
+
+            config BSP_USING_WDT2
+                bool "Enable WDT2"
+                default n
+        endif
+
     menuconfig BSP_USING_PWM
         bool "Using PWM"
         select RT_USING_PWM
@@ -63,9 +218,13 @@ menu "General Drivers Configuration"
             config BSP_USING_PWM3
             bool "Enable PWM 3"
             default n
-
         endif
 
+    config BSP_USING_RTC
+        bool "Enable RTC"
+        select RT_USING_RTC
+        default n
+
     config BSP_USING_SDH
         select RT_USING_SDIO
         select RT_USING_DFS
@@ -80,4 +239,5 @@ menu "General Drivers Configuration"
         select RT_USING_LWIP
         select RT_USING_POSIX_FS
         select RT_USING_POSIX_SOCKET
+
 endmenu